Self-supported Ni2P nanotubes coated with FeP nanoparticles electrocatalyst (FeP@Ni2P/NF) for oxygen evolution reaction

Bimetallic phosphides have been widely investigated as electrocatalysts for oxygen evolution reaction (OER) due to their efficient activity and environmental friendliness. While the reasonable design and controllable synthesis of bimetallic phosphide with typical nanostructure is still a great challenge. Hence, we put forward a novel and straightforward way for constructing FeP nanoparticles coated Ni₂P ultrathin nanotube arrays on the surface of Ni foil (FeP@Ni₂P/NF), which is synthesized through two steps of electrodeposition and subsequent in-situ phosphorization process. The obtained FeP@Ni₂P/NF shows excellent electrochemical activity for OER, and it only needs potential of 1.52 V vs. RHE to reach the current density of 50 mA cm⁻² in an alkaline media. The excellent electrocatalytic activity of FeP@Ni₂P/NF mainly benefits from: (i) the synergistic effect between FeP and Ni₂P promoting electron transfer; (ii) the formation of the unique 3D ultrathin nanotube arrays increasing the quantity of active sites and avoiding the agglomeration of catalysts during testing. In addition, the influence of reaction condition on the electrochemical activity for OER has also been investigated through altering the phosphorization temperature of precursor.     

硫酸镍煅烧的实验研究

硫酸镍煅烧可以产生镍氧化物,作为制备氧化镍的原料。以六水硫酸镍为原料,采用热重-差热分析（TG-DTA）、X射线衍射（XRD）分析研究了其煅烧过程并对产物进行了表征。研究结果表明,硫酸镍煅烧过程分为3个阶段：第一阶段（27~250 ℃）及第二阶段（250~600 ℃）为脱水阶段;第三阶段（600~900 ℃）为分解阶段。在煅烧温度为850 ℃、煅烧时间为30 min、粒度为74~147 μm条件下,硫酸镍煅烧产物为氧化镍。     

苏通GIL运输专用机具动力电池类型探讨

GIL运输专用机具是为安全、可靠、高效地完成苏通GIL综合管廊工程GIL单元的运输任务而研制的专用机具,其中动力电池系统设计是整机设计的重点之一。通过对各种常见动力电池优缺点的分析,并结合苏通GIL运输专用机具对动力电池的需求分析,确定了动力电池系统的技术路线,为苏通GIL运输专用机具的研制提供了坚实的基础。     

高镁镍渣-磷石膏基复合胶凝材料的制备与性能评价

采用机械研磨的方式将高镁镍渣（HMNS）和磷石膏（PG）筛分至不同粒度，评价了掺不同粒度高镁镍渣和磷石膏复合胶凝材料的力学性能，并对强度形成机制进行了分析。评价了各种配比下浆体的抗压强度和体积稳定性，并分析了其作用机制。试验表明：以HMNS∶PG∶富钙硅质材料ZL=5.4∶3.6∶1配比制得试样的28 d抗压强度为4.43 MPa；室温环境下养护56 d，SP6线性收缩为1.02×10-3 mm/mm，体积稳定性优良；水化产物Ca(OH)2更少，Ca（OH）2与HMNS-PG体系反应生成了CSH凝胶和AFt，结构更为稳定。     

Separation and recovery of Ni from copper electrolyte by crystallization of nickel ammonium sulfate double salt

The separation and recovery of Ni from the copper electrolyte by crystallization of nickel ammonium sulfate double salt were studied. It is found that the solubility of copper sulfate at the same temperature is less than that of nickel sulfate, while the solubility of copper ammonium sulfate is greater than that of nickel ammonium sulfate. So, by adding (NH₄)₂SO₄, the Ni can be selectively crystallized from the copper electrolyte. By adding (NH₄)₂SO₄ at the molar ratio of (NH₄)₂SO₄/NiSO₄ ≤0.8, and crystallizing at —15 °C for 10 h, the Ni in the copper electrolyte can be crystallized in the form of Ni(NH₄)₂(SO₄)₂·6H₂O. The qualified product of NiSO₄·6H₂O can be obtained by pyrolyzing the crystals, dissolving the pyrolysis product in water, and then concentrating the dissolved solution for crystallization. The method of double salt crystallization is a clean, environmentally-friendly, cost-effective and efficient method for separating and recovering nickel from copper electrolyte.     

现代镀覆技术 第二部分──化学镀镍(续4)

给出了各种实用的化学镀镍配方及其工艺条件。     

Promoted electrocatalytic performance of palladium nanoparticles using doped-NiO supporting materials toward ethanol electro-oxidation in alkaline media

Electrocatalyst support materials play significant role in the performance, durability and commercialization of fuel cells. This research work describes the preparation of metal oxide (nickel oxide (NiO), cobalt (Co) and copper (Cu) doped NiO) support materials on meshed titanium (Ti) substrate via a simple electro-deposition method for their application as novel support material for palladium (Pd) catalyst. Field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD) techniques are employed to study morphology, composition and structure of fabricated electrodes, respectively. The electrocatalytic performance of fabricated electrodes toward ethanol oxidation reaction (EOR) in alkaline solution is examined by the cyclic voltammetry (CV), chronoamperometry (CA) techniques. Low peak potential (−0.2 V), increased peak current density (62.54 mA cm⁻²) and large electrochemical active surface area (16.02 m² g⁻¹) were remarkable properties of Pd/Cu–NiO/Ti electrode. The results of other electrochemical measurements, CO-striping voltammetry, long-term stability and electrochemical impedance spectroscopy (EIS) revealed that the Pd/Cu–NiO/Ti electrode has the privileged electrocatalytic performance for EOR relative to other prepared electrodes. Accordingly, the Pd/Cu–NiO/Ti can be considered as a hopeful electrode for ethanol electro-oxidation reaction in DEFCs.     

单晶/多晶镍轴向拉伸力学性能的分子动力学模拟

为提高航空发动机推重比采用整体叶盘新技术却带来了盘叶连接区域高风险失效问题。本文采用分子动力学对连接区单晶/多晶镍(SPSNi)的力学性能进行模拟,首先通过对比了不同晶态镍拉伸原子图。发现,由于单晶/多晶界面的存在使得拉伸后界面处的非晶化程度加剧,易于孔洞萌生,加剧了SPSNi突然断裂的风险。最后重点研究了单晶/多晶镍的应变率效应与温度效应。当应变率大于1í10_⁸s_^-1小于2í10_¹⁰s_^-1时,SPSNi对加载应变率几乎不敏感,屈服强度小幅上升。超过2í10_¹⁰s_^-1之后,其屈服强度随着应变率的增加而迅速下降。这是因为在高应变率下,SPSNi的FCC原子大规模迅速转变为无序的非晶结构,导致了晶体镍承载能力迅速下降。可以将应变率2í10_¹⁰s_^-1作为SPSNi拉伸变形的阈值。不同温度下,SPSNi屈服强度随温度的增大而线性下降。这是由于在温度的影响下,位错网络的初始镶嵌结构逐渐变得不规则,初始失配应力随着温度的升高而下降。     

基底表面质量对ZK60镁合金镀镍层性能的影响

镁合金表面镀镍被广泛运用于镁合金工件防腐,而镀层的起泡和脱落严重影响工件的使用寿命。本实验以ZK60镁合金为研究对象,分析了不同工件基底表面质量对镀镍层性能的影响机制。研究表明:基底表面存在的划痕和点蚀坑会显著降低镀镍层质量,引起镀层的起泡和脱落。基底表面的划痕会被保留到镀镍层中,引发镀层变薄,应力集中等问题,增加镀层开裂的几率。点蚀坑中的杂质与镁基底有不同的电化学特性,会导致镀层减薄和结合不牢。因此,提高镁合金工件基底表面光洁度、清除基底表面点蚀坑是提高镁合金镀镍层性能的必要措施。     

Effects of heat treatment on microstructure and mechanical properties of Inconel 625 alloy fabricated by wire arc additive manufacturing process

The microstructure and mechanical properties of Inconel 625 alloy fabricated by wire arc additive manufacturing process were evaluated under as-prepared and heat-treated conditions. A dendritic Ni-based solid solution phase along with (Nb, Ti)C carbide, Laves, and δ-Ni₃Nb secondary phases were developed in the microstructure of the as-prepared alloy. Solution heat treatment led to the dissolution of Laves and Ni₃Nb phases. In addition, dendrites were replaced with large columnar grains. Aging heat treatment resulted in the formation of grain boundary M₂₃C₆ carbide and nanometric γ″ precipitates. Hardness, yield and tensile strengths, as well as elongation of the as-prepared part, were close to those of the cast alloy and its fracture occurred in a transgranular ductile mode. Solution heat treatment improved hardness and yield strength and declined the elongation, but it did not have a considerable impact on the tensile strength. Furthermore, aging heat treatment caused the tensile properties to deteriorate and changed the fracture to a mixture of transgranular ductile and intergranular brittle mode.